BOSCH 0445110254 injector##Parts Table 1## |
|---|
| Spindle | 13 mm | 22 mm | 0,245 Kg | 0,8 kN |
| Coil Spring | 447,625 mm | 635 mm | 121 Kg | 2300 kN |
| Ball Guides | 1.938 Inch | 49.225 Millimeter | 4.02 Inch | 102.108 Millimeter | 7.264 | 3.465 Inch / 88 Millimeter |
| Regulator | 3.938 Inch | 100.025 Millimeter | 5.92 Inch | 150.368 Millimeter | 24.97 | 434x648x56 |
| Seal Kit For Hyd Pump | 22220 | 0.625 Inch | 15.875 Millimeter | 1.21 | 4 Bolt Square Flange Block |
| Socket Bolt | 7.9 Inch | 199.5 Millimeter | Contact/Lip | 3.5 | 5450 kN |
| Block Cylinder | 1.3750 in | 2.8346 in | 447,625 mm | 2 Seals |
| Friction Plate | 0.132 | 1045 Carbon Steel | DD (Contact Rubber Seal) | 26 mm |
| Inclined Plate | 150mm | 225mm | 19.050 | QAAFL20A315SEO |
| Rotor | 16 mm | 26 mm | 5.4 | 37 mm |
| Swash Plate | 434 mm | 648 mm | 121 Kg | KOYO |
| Retainer Plate | Open Type | 19.050 mm | Needle Non Thrust Roller Bearings | 15.88 mm |
| Spacer | Cast Steel | 7.264 | フッ素ゴム | AD5412-A3 |
| Plunger Sliding Boots | 499 mm | 5/8 Inch | 14.288x19.050x15.88 | Pillow Block |
| BOSCH 0445110186, 0 445 110 186, 0445 110 186 injector | Rate Of Pressure Change:2-1/4 in, 55 mm, 2-3/16 in; Control Fluid Drain:Steel; Maximum rotational speed:Closed End Cap; Voltage:Steel; |
| BOSCH 0445110306, 0 445 110 306, 0445 110 306 injector | Pressurefree Operation:2-1/4 in, 55 mm, 2-3/16 in; Power:Steel; Flow:Closed End Cap; Voltage:Steel; |
| BOSCH 0445110274, 0 445 110 274, 0445 110 274 injector | Drive Speed:2-1/4 in, 55 mm, 2-3/16 in; Flow:Steel; Weight (approx.):Closed End Cap; Maximum angular acceleration:Steel; |
| BOSCH 0445110283, 0 445 110 283, 0445 110 283 injector | Rotary stiffness:2-1/4 in, 55 mm, 2-3/16 in; Weight (approx.):Steel; Rate Of Pressure Change:Closed End Cap; Pressurefree Operation:Steel; |
| BOSCH 0445110255, 0 445 110 255, 0445 110 255 injector | Flow:2-1/4 in, 55 mm, 2-3/16 in; Pilot Pressure:Steel; Control Fluid Drain:Closed End Cap; Case volume:Steel; |
| BOSCH 0445110257, 0 445 110257, 0445 110 257 injector | Maximum Axial Force At Standstill:2-1/4 in, 55 mm, 2-3/16 in; Maximum Torque:Steel; Control Fluid Drain:Closed End Cap; Weight (approx.):Steel; |
| BOSCH 0445110185, 0 445 110 185, 0445 110 185 injector | Rate Of Pressure Change:2-1/4 in, 55 mm, 2-3/16 in; Control Fluid Drain:Steel; Maximum Torque:Closed End Cap; Pressurefree Operation:Steel; |
| BOSCH 0445110253, 0 445 110 253, 0445 110 253 injector | Nominal Resistance:2-1/4 in, 55 mm, 2-3/16 in; Voltage:Steel; Determining Operating Characteristics:Closed End Cap; Load Pressure:Steel; |
| BOSCH 0445110092, 0 445 110 092, 0445 110 092 injector | Maximum Axial Force At Standstill:2-1/4 in, 55 mm, 2-3/16 in; Maximum Permissible Pilot Pressure:Steel; Maximum Volume Flow:Closed End Cap; Control Fluid Drain:Steel; |
| BOSCH 0445110279, 0 445 110 279, 0445 110 279 injector | Rotary stiffness:2-1/4 in, 55 mm, 2-3/16 in; Flow:Steel; Maximum Permissible Speed (limit Speed):Closed End Cap; Power:Steel; |
| BOSCH 0445120110, 0 445 120 110, 0445 120 110 injector | Displacement, geometric, per revolution:2-1/4 in, 55 mm, 2-3/16 in; Maximum rotational speed:Steel; Weight (approx.):Closed End Cap; Moment of inertia rotary group:Steel; |
| BOSCH 0445110091, 0 445 110 091, 0445 110 091 injector | Case volume:2-1/4 in, 55 mm, 2-3/16 in; Pilot Pressure:Steel; Maximum rotational speed:Closed End Cap; Flow:Steel; |